 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NEW 1.1mm Pitch Low Profile Compression Connectors DF26 Series Compression Connectors -Mating height: 1.2mm and 1.7mm Press down Press in sFeatures 1. Low Profile Connectors are available in heights : 1.2mm and 1.7mm. 3. One-Piece Connector These connectors support cost reduction requirement since there is no need for a mating half connector. This design also permits a reduction in the number of assembly steps. 2. Miniature, Space-Saving Design The space-saving design of these connectors permits increase in the mounting density as compared to equivalent products. 4. Variations Number of Contacts Mating Height 1.2mm 1.7mm 9 Contacts 16 Contacts 18 Contacts Under development sApplications LCD, cellular phones, notebook computers, miniature office automation equipment, and miniature consumer products. Item Product Before Contact Contacting (Effective Mating Height) 1.55mm 1.2mm Press Pressindown 1.9mm 1.55mm 1.2mm 2.05mm Press Pressindown 1.2mm 1.7mm 2.4mm 2.05mm 1.7mm 1.7mm 2003.7 1 sProduct Specifications Rating Current rating Voltage rating 0.5 A 50 V AC Operation Temperature Operation Humidity -35c to 85c (Note 1) Storage Temperature -10c to 60c (Note 2) Storage Humidity 20% to 80% 40% to 70% (Note 2) Conditions 100 V DC 150 V AC / one minute 100 mA Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions 96 hours at temperature of 40 2c and humidity of 90% to 95% Temperature: -55c +5c to +35c +85c +5c to +35c Time sequence: 30 10 30 10 (Minutes) 5 cycles 50 stroke cycles Reflow soldering: At recommended temperature profile Manual soldering: Soldering iron temperature 300c, 3 seconds Item 1. Insulation resistance 500 M ohms min. Specification 2. Withstanding voltage No flashover or insulation breakdown 3. Contact resistance 50 m ohms max. 4. Vibration 5. Humidity No electrical discontinuity of 1s or more Below the contact resistance standard value. Insulation resistance: 500 M min. Below the contact resistance standard value. Insulation resistance: 500 M ohms min. Below contact resistance standard value No deformation of the insulator parts affecting performance. 6. Temperature cycle 7. Stroke life 8. Resistance to soldering heat Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to connectors stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. sMaterials Item Compression Part Insulator Contacts Material LCP Phosphor bronze Finish Color: Black Gold plating Remarks UL94V-0 ---------- sOrdering Information DF26 # 1.2 - * CP - 1.1 V ( * * ) 1 1 Series name: DF26 2 Boss type A: With boss 2 3 4 5 6 7 8 8 Packaging (51): Embossed tape packaging (2,000 pieces per reel) 0.1 micron gold plated (66): Embossed tape packaging (2,000 pieces per reel) 0.5 micron gold plated 4 Number of contacts: 9, 16 5 Connector type CP: Single row compression 3 Mating height 1.2: 1.2mm 1.7: 1.7mm 6 Contact pitch: 1.1mm 7 Contact type V: Straight SMT 2 sCompression Connectors (Straight SMT) for 1.2mm Mating 1.6 +0.2 -0.1 A 0.3 Condition at full stroke 0.7 3.6 0.3 0.35 0.05 P= 1.1 0.1 0.3 0.05 1.2 MAX 1.97 0.1 + - 0 0.54 -0.1 C0.15 0 +0.1 0 2.7 0.2 BPCB Mounting Pattern Connector Mounting Surface Side 1.950.03 C0.05 5 .0 +0 0 Connector Contact Side 1.30.2 (N ot e) Boss hole of mounting board side . O0 8 3 +0.1 0 1.9 0.1 boss (Note) 0 O0.7 -0.1 B 0.2 0.9 0.1 0.550.03 P=1.10.05 B0.05 Gold plating 0.8 0.03 P=1.10.05 B0.05 [Specification number] ---- * *, (* *) (51): Gold plating, embossed tape packaging (2,000 pieces per reel) Unit: mm Product No. DF26A1.2-09CP-1.1V(**) DF26A1.2-16CP-1.1V(**) DF26A1.2-18CP-1.1V(**) Note: Order by number of reels. HRS No. CL661-0002-5-** CL661-0003-8-** Under development Number of Contacts. 09 16 18 A 12.3 20.0 22.2 B 08.8 16.5 18.7 C 11.0 18.7 20.9 Embossed width 24 32 32 Notes With boss 1.7 +0.1 0 3 sCompression Connectors (Straight SMT) for 1.7mm Mating Cross-sectional Diagram 1.6 +0.2 -0.1 A 0.3 Condition at full stroke 2.23 0.2 3.6 0.3 0.12 0.05 0.350.05 ( 0.6 ) B0.2 P=1.10.1 1.7 MAX 0.3 0.05 1.970.1 2.4 0.1 Boss (Note) 0 0.54 -0.1 0 O0.7-0.1 C0.15 2.7 0.2 0.9 0.1 BPCB Mounting Pattern Connector Mounting Surface Side 1.950.03 C0.05 5 .0 +0 0 Connector Contact Side 1.30.2 1.7 +0.1 0 (N ot e) Boss hole of mounting board side O0 .8 3 +0.1 0 0.550.03 P=1.10.05 B0.05 Gold plating 0.8 0.03 P=1.10.05 B0.05 [Specification number] ---- * *, (* *) (66): Gold plating, embossed tape packaging (2,000 pieces per reel) Unit: mm Product No. DF26A1.7- 9CP-1.1V(**) Note: Order by number of reels. HRS No. CL661-0008-1-** Number of Contacts 9 A 12.3 B 8.8 C 11.0 Embossed width 24 Notes With boss 4 BEmbossed Carrier Tape Dimensions J-J O1 8 0.1 J G 1.75 0.1 .5 + 0 0 .05 2 0.1 4 0.1 G-G C0.1 B 0.1 A 0.3 H D0.2 H J K G t= 0.3 0.05 Unreeling direction H-H + 0 0 .05 K 1.05 0.15 3.9 0.2 R0 0.8 0.2 Reel Dimension 20.5 Product name label O1.5 feed hole depth O13 0.2 O3302 ( O80) 0.8 O21 E +20 F MAX 0.2 0.05 .7 5 Unit: mm Product No. DF26A1.2-09CP-1.1V DF26A1.2-16CP-1.1V * DF26A1.2-18CP-1.1V DF26A1.7-09CP-1.1V * Under development Number of Contacts 09 16 18 09 A 24 32 32 24 B ---------28.4 28.4 ---------C 11.5 14.2 14.2 11.5 D 2.4 2.4 2.4 2.9 E 24.4 32.4 32.4 24.4 F 30.4 38.4 38.4 30.4 With boss Notes 5 BPrecautions for Use 1. Recommended Temperature Profile Temperature Preheating: IR Reflow 150c 2355c 220c min 30 to 90 seconds 10 seconds max 10 to 30 seconds Soldering: 250c 200c 150c 100c Maximum 240c 220c Preheating Soldering 50c 0c 0 50 100 150 200 Time(Sec.) Note1: Up to 2 cycles of reflow soldering are possible under the same conditions, provided that there is a return to normal temperature between the first and second cycle. Note2: The temperature profile indicates the board surface temperature at the point of contacts with the connector terminals (for surface mounted receptacle). 2.Recommended manual soldering 3.Recommended screen thickness 4.Board warpage 5.Cleaning conditions Manual soldering: 29010c for 3 seconds 0.15mm Maximum of 0.03mm at the connector center, with both ends of the connector as reference points. Refer to "Nylon connector Use Handbook". sExcessive twisting when mating/un-mating may cause damage to the connector. sThe contacts are of an exposed design and touching them with bare hands may cause breakdown of the elements due to contact faults or static electricity. 6.Precautions 6 |
Price & Availability of DF26A17-9CP-11V
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |